horizontal slurry pump factory

Latest articles



Popular articles

Latest articles

Links

  • pet

  • 3, pay attention to the width of the cage seam

  • The entire steel surface is protected, and the melted zinc is easily coated evenly, whether in the interior of the pipe fitting in a depression, or in any other corner where the coating is difficult to access. The hardness of galvanized coating is greater than that of steel. The Eta layer of the upper layer of Z is only 70 DPN hardness, so it is easy to be dented by collisions. However, the hardness values of the lower layer of Zeta layer and delta layer are 179 and 211 DPN respectively, which are higher than that of the iron material of 159 DPN. Therefore, its impact resistance and wear resistance are quite good.

  • Steel wire mesh is finished by fine welding of active welding equipment. The material can be divided into cold wire drawing, hot galvanizing, cold galvanizing, dip plastic and so on. To be used for bridge reinforcement, bridge deck pavement, building reinforcement and so on.

  • After the appearance of barbed wire black spots, you can choose the appearance of treatment to deal with this problem, such as galvanized, spray painting, dip plastic to deal with, after the appearance of welding mesh appearance smooth and bright, beautiful and generous.

  • There is no adhesion test of powder spraying or fluorocarbon spraying on packaged galvanized wire, but there are two points for reference: first, in sealed or air-free environment, non-metallic volatiles can corrode zinc coating; Second, zinc at higher than 230 degrees (c) will cause the matrix metal brittle. And powder spraying and fluorocarbon spraying are to be baked at a higher temperature and in a sealed environment, causing rapid corrosion of zinc, resulting in loose corrosion film resulting in coating adhesion decline, and even lead to (matrix) steel wire brittle situation may exist.

  • Galvanized hexagonal net is a kind of galvanized metal wire mesh, mesh shape is hexagonal.

  • The use of spring in a specific environment, there will be some special requirements for steel wire, such as: the use of spring in corrosive media, must have good corrosion resistance function. Precision instruments used in the spring, should have long-term stability and sensitivity, temperature coefficient to be low, high quality elements, after effect to be small, elastic modulus to be stable.

  • As we all know, stainless steel barbed rope is installed in the outdoor, after a long time of exposure to the sun is easy to rust, once rust service life will end. So want to extend the service life of stainless steel barbed rope must prevent rust. In general, in order to prevent rust, we will choose to spray stainless steel barbed rope.

  • The different spacing of the thorn rope is mainly in order to save costs to consider, because if they are too close, then obviously a little waste of resources, but the installation is too sparse will not work. Usually the bottom spacing is about 10cm, and the top is up to 20cm, this is because the higher the place is more difficult to climb over, usually more than one meter without the help of tools it is difficult for ordinary people to climb over, and the bottom because of the relatively tight can prevent personnel from drilling in the past.

  • pet

  • With the improvement of people’s living standards, now many families are raising some small pets, these small pets need a stable nest, pet cage has become a more important choice of people, each pet habits and living habits will choose to adapt to the cage.

  • galvanized

  • If adult dogs and puppies touch noses out of love, then adult dog nose touching is more meaningful. For example, dogs can touch their noses to communicate where food is safe and whether people or other animals are in danger.

  • The bonding and anchoring function between the cold rolled ribbed steel bar and concrete is outstanding. In reinforced concrete structure, the width of black iron wire processing crack is smaller than that of circular steel bar, even than that of hot rolled thread steel bar. Therefore, it is used in the component, which fundamentally eliminates the phenomenon of steel wire sliding and damage, and improves the load bearing ability and crack resistance ability of the component end.

  • Hot dip galvanizing is in the hot melt zinc liquid dip plating, production speed, thick but uneven coating, the market allows the thickness of 45 microns, up to 300 microns above. It is dark in color, consumes more zinc metal, forms infiltration layer with base metal, and has good corrosion resistance. Hot dip galvanizing can be maintained for decades in outdoor environment. The protection of zinc coating on iron matrix has two principles: on the one hand, although zinc is more active and easy to oxidize than iron, but its oxide film is not as loose and compact as iron oxide. The dense oxide layer formed on the surface inhibits the further oxidation of zinc in the interior.

  • welding

  • Post time: 22-07-22

  • The national standard on the use of wire mesh standards have certain requirements, diameter and mesh size matching use, rather than simply diameter size, on the plaster layer to use is mesh should not be greater than 20×20, diameter is not easy to be less than 1mm, light selection diameter is not much significance, choose 40×40×0.9 and choose 10×10×0.6 wire mesh, Which is better, I’m afraid is 10×10×0.6.

  • Post time: 04-04-23

  • galvanized

  • welding

  • Long-term exposure to such impurities will result in transition and gap corrosion. The direct solution to this phenomenon is to strengthen the coating of the material to avoid corrosion. Improve the quality of galvanized iron wire, can use the wire that had plated zinc beforehand to pull out when making galvanized iron wire, won’t appear the phenomenon of bad mechanical properties. The toughness of the wire is 15 to 25 per cent higher than that of the drawn and galvanized wire, and in some cases slightly stronger than that of the polished wire.
  • Galvanized wire is coated with a layer of stable zinc on the outside of the wire, and the zinc layer is used to protect the wire and make the service life of the wire longer. In the production of galvanized wire, the wire should be pickled. Pickling is to use some acid mist or acid liquid to wash away some oxides on the surface of iron, that is, rust, and some other corrosion, to achieve the purpose of cleaning iron, so that zinc will fall off when galvanized.

  • Replace the column that corroded or misinterpreted and so on resulting in the loss of effect, place the replacement area together from the beginning, and reinforce the column with unstable pile foundation in time. The second is about the protection of galvanized barbed rope itself, to repair the damaged local, will be severely replaced by rust.

  • Post time: 28-07-22
  • The positive and negative twisting barbed wire is less than 3 cents per meter, and the corresponding 12 hot dip galvanized barbed wire is 5 cents per meter, no matter from the service life, tensile strength, rust prevention effect is no worse than the 12 iron wire

  • The application of black iron wire in the process is mainly through the hot metal billet rolled into 6.5 mm wire rod, and then put it into the wire drawing device into a different diameter line, and then gradually reduce the aperture of the wire drawing disk, cooling and annealing, coating and other processes, made into a variety of different specifications of iron wire, this kind of iron wire and ordinary black iron wire compared, will be softer, Softness is also very uniform, color is consistent, widely used in the construction industry, mining, chemical industry, welding mesh, welding hanger, reprocessing industry.

  • When galvanized wire out of the light plating should be carried out light treatment. The bath temperature of galvanized wire should be controlled well. Galvanized wire, also known as hot dip zinc and hot dip galvanized, is an effective way of metal corrosion prevention, mainly used in various industries of metal structure facilities. It is to immerse the steel parts after rust removal into the molten zinc liquid at about 500℃, so that the surface of the steel member is attached with zinc layer, so as to play the purpose of anticorrosion.