submersible slurry pump with agitator manufacturer

Latest articles



Popular articles

Latest articles

Links

  • Hexagonal mesh is a metal wire woven Angle mesh (hexagonal) made of wire mesh, the use of metal wire diameter is based on the size of the hexagonal and different. Also known as: twist flower net, stone cage net, gabion net, flood control network.

  • Galvanized wire coating is galvanized, aluminum plated, coated with nylon or plastic, etc. Zinc is divided into thin coating of steel wire after plating and thick coating of galvanized steel wire after drawing. The mechanical properties of thick coating are reduced compared with smooth steel wire rope, which should be used in severe corrosion environment. It is more resistant to corrosion, wear and heat than galvanized wire rope, using the first plating and then drawing method of production. Coated nylon or plastic wire rope is divided into two kinds of coated rope and coated stock after the rope.

  • The external environment has a great influence on the storage of cold drawn wire. Especially during the rainy season, special attention should be paid to the air humidity of workshops and warehouses. It is recommended to use moisture test paper with a value between 8 and 10. If the PH value is high, attention should be paid to the corrosion of the internal cold drawing wire. Cold drawing wire in normal environment storage for two years no problem, cold drawing wire will not be corroded. However, it is necessary to place the coil gently during the handling process to avoid the winding position leading to the cable is not smooth.

  • The wire after the first plating, its strength limit is also higher than the first plating, plated zinc and then made of wire not only toughness and high strength. There is a lower figure in the strength limit of galvanized iron wire because of the quality of zinc, because the strength of zinc technology is several times smaller than the wire itself. It is difficult to hot-dip galvanize drawn wires, and it is impossible for finer and very fine wires to be coated with the desired thickness of smooth zinc.

  • Annealed wire is mainly through low carbon steel heating, hot drawing, constant temperature and other processes made into soft iron wire, because in the use of different, so there are different in the production process, made of a variety of specifications. Annealed wire can be widely used, mainly because annealed wire and other kinds of iron wire, has many advantages.

  • Post time: 06-05-22
  • Post time: 06-02-23
  • Generally speaking steel does not rust easily with chromium content of 10.5%. The higher the content of chromium and nickel, the better the corrosion resistance, such as 304 material nickel content in 8-10%, chromium content of 18-20%, such stainless steel in general is not rust.
  • 6, barbed rope protection network layout should be according to the road boundary terrain necessary renovation, flat section level set, slope section slope or step set.

  • steel

  • building

  • 6, passivation to remove hydrogen parts should be passivation after the removal of hydrogen, passivation before the application of 1%H2SO4 or 1% hydrochloric acid activation 5~15s. Passivation shall be treated with colored chromate unless otherwise specified in the design drawings.

  • Post time: 05-06-23

  • The production process is to roll the hot metal billet into 5mm thick steel, and then put it into the wire drawing device, draw into different diameters of the line and gradually reduce the aperture of the wire drawing disk. Production process through cooling, annealing, coating and other processing technology, and then made into a variety of different specifications of galvanized wire. Galvanized wire production because of simple process, wide application, early development. Galvanized wire or steel wire is a cold working product of steel wire, and the material used is generally low carbon steel or stainless steel.

  • Crevice corrosion is a kind of corrosion in small area, especially in concealed position, which can form vicious corrosion cycle. Almost all the crevice corrosion can occur in a metal alloy, with gas containing active anionic neutral medium Z is easy to cause crevice corrosion, crevice corrosion often occurs in the aperture of 0.025 to 0.1 mm, because of long time gathered, the cracks will exist a series of impurities, coupled with the external environment of damp easily corrode the area of the gap is small.

  • Post time: 22-07-22

  • Customers do not need to worry about the impact of the production cycle when ordering products from the thorn rope factory, because the overall treatment is now focused on the waste gas, so the production of thorn rope should be said to have the least impact. Customers ordering products in the thorn rope factory can rest assured that the delivery time this piece, can provide customers with goods on time. If the production cycle is not affected, then customers will be more assured of the thorn rope factory.

  • Long-term exposure to such impurities will result in transition and gap corrosion. The direct solution to this phenomenon is to strengthen the coating of the material to avoid corrosion. Improve the quality of galvanized iron wire, can use the wire that had plated zinc beforehand to pull out when making galvanized iron wire, won’t appear the phenomenon of bad mechanical properties. The toughness of the wire is 15 to 25 per cent higher than that of the drawn and galvanized wire, and in some cases slightly stronger than that of the polished wire.

  • Blade thorn rope because the volume is relatively large, so the thorn rope factory is used to packaging.

  • The antisepsis of these materials is very different, the use of life is not the same. Cold galvanized cattle net, also known as electroplating, galvanized amount is small, rust in rain, but the price is cheap, the service life is 5-6 years. The amount of zinc on hot dip galvanizing (low zinc and high zinc) is about 60g to 400g, the service life is about 20-60 years, and the corrosion resistance is general.

  • Post time: 30-05-22
  • Post time: 23-02-23

  • galvanized

  • Post time: 17-06-22
  • Post time: 29-01-23
  • Some welding methods of galvanized steel mesh will reduce the quality of low carbon steel welded joints, such as electroslag welding. Because the line energy is high, the coarse grains in the heat affected zone of welding will become very coarse, leading to a severe reduction in impact toughness. After welding, it is necessary to normalize with refined grains to improve impact toughness.