rubber lined slurry pump spare parts

Latest articles



Popular articles

Latest articles

Links

  • There are many production links of blade barbed rope, and the finished product can only be produced after several times of production. Roughly, there are four or five links.

  • In the corner area, the zinc layer is often thicker than other places, and has good toughness and abrasion resistance. And other coatings in this corner, often Z thin Z is not easy to construction, Z is easy to hurt, so often need to be maintained. Even if there’s a lot of mechanical damage or something. Causing a small layer of zinc to peel off, leaving the iron base exposed, the surrounding zinc layer will act as a sacrificial anode to protect the steel from erosion.

  • When laying steel wire mesh, according to the laying method from the middle to both sides in turn. Wall plastering engineering use wire mesh material is generally two kinds: one is electroplating, the other is hot dip galvanized. The former has low cost and a wide range of use. The cost of hot-dip galvanized material is slightly higher than that of electroplating, and the cost is high and the life is good to prevent rust. Hot dip galvanizing is in the case of heating plating. After the zinc is melted into liquid form, the base metal is immersed in it so that the zinc interpenetrates with the base metal and binds so tightly that there are no other impurities or defects left in the process.

  • galvanized

  • ③ The galvanized iron wire shall not be damaged when it is tightened.
  • Post time: 06-05-23
  • If the solder joint is too deep, it is not good, although the welding is more solid, but the bearing capacity of the solder joint is greatly reduced, once the pressure exceeds the load range, it will fracture at the solder joint, so it is more dangerous to use. Large galvanized wire production process of low carbon steel wire cleaning cleaning agent, should have no effect on the binding force of the coating, no corrosion of low carbon steel wire. Production process, acid activation acid activation liquid, should be able to remove the surface of low carbon steel wire corrosion products, oxide film, no corrosion to the matrix.

  • At present, there are two processing methods of blade stabbing rope. One is to make it into a spiral shape, and then make a clip treatment. It is not only our common spiral blade stabbing rope, but also a single spiral blade stabbing rope without clip, but even a single helix can not stretch it to a relatively straight. This is mainly because the blade barbed rope is wrapped and wound at the same time, so it can only be spiral.

  • galvanized

  • Post time: 24-11-22
  • Post time: 04-11-22

  • Hexagonal

  • Post time: 17-05-22

  • The hook mesh is a good material for flood control and flooding. Can also be used for arts and crafts manufacturing, mechanical equipment transport network mountain beautification network – high strength steel wire grid (hook mesh, diamond mesh) hook mesh mountain protection application principle, hook mesh interests, mesh uniform, flat, woven concise, hook woven, beautiful and generous, net, net width, wire diameter is thicker, not easy to corrosion, long life, strong usefulness.

  • 2. When the weather is too dry and humid, remember to blow dry the cage or move it to a place with heating to prevent dry crack damage.
  • 2. Drying: Dry the washed steel wire through hot air or other drying equipment to remove water.
  • Post time: 16-08-22

  • The external environment has a great influence on the storage of cold drawn wire. Especially during the rainy season, special attention should be paid to the air humidity of workshops and warehouses. It is recommended to use moisture test paper with a value between 8 and 10. If the PH value is high, attention should be paid to the corrosion of the internal cold drawing wire. Cold drawing wire in normal environment storage for two years no problem, cold drawing wire will not be corroded. However, it is necessary to place the coil gently during the handling process to avoid the winding position leading to the cable is not smooth.

  • 4) Steel wire welding process: sometimes when you buy a pet cage, it will crack in a few days. When you buy it, you can also look at whether the welding is smooth and whether the welding area is large. Generally speaking, the welding surface is large, it must be much stronger. There is also a very important welding point treatment, the quality of the cage, the welding surface must be smooth, will not damage the pet, but the quality is not good, it is easy to ignore these details, a small thorn, may let your dog injury.

  • Pet

  • Stainless steel is short for rust acid steel, air, steam, water and other weak corrosion medium or stainless steel is called stainless steel; And the chemical corrosion resistance medium (acid, alkali, salt and other chemical etching) corrosion of steel called acid steel.

  • The drawing process of the product drawing process has a great influence on the product function. Generally, a large total surface reduction rate of about 90% (see area reduction rate) and a small pass surface reduction rate (about less than 23%) are selected to ensure the endurance of the product. On the high strength spring steel wire, drawing should control the exit temperature of each passage of the steel wire is lower than 150℃, to avoid the steel wire due to strain aging and appear to change the crack, which is the formation of steel wire scrap the primary disadvantage.